1
General Questions / Fuel Level Sending Unit
« on: September 01, 2022, 04:13:25 PM »
Anybody know the exact MFG/Part Number for the fuel level sending unit Hurricane provides?
News:
Welcome to the NEW Hurricane Motorsports discussion group.
Take time to browse around and get familiar.
Very similar to the previous forum but
there are some subtle differences
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
For Sale / Hurricane provided seats for sale
« on: August 02, 2022, 02:16:58 PM »
Have a couple new seats that came with the kit from Hurricane (Cobra brand) brand new. could use some additional attention to finishing and gluing on underside of cushions. $400.00 plus shipping. Shoot me a text or email. I usually ignore numbers I don't recognize due to all the spam calls out there so just shoot a text.
Bruce 972-342-8936 or bnelson7093@yahoo.com
Bruce 972-342-8936 or bnelson7093@yahoo.com
3
General Questions / supplied electric fan
« on: May 14, 2022, 07:07:24 PM »
Can anyone tell me what the CFM on our supplied electric fan is? Or make and model? I'm getting a little hot at idle in traffic. Was at the C-10 national truck show at Texas Motor Speedway today and one of the vendors there had some fans that I would swear pull four times the CFM that ours does. Think I'd like to try one at least double what ours puts out.
4
General Questions / drivers side mirror mounting
« on: May 04, 2022, 04:23:12 PM »
What's everyone doing to mount the drivers side mirror. I haven't decided on front of door or on fender yet, but as far as mounting method on door? Cant get to anything to put nuts on. Are you using rev nuts? Or just using sheet metal screws into the glass?
5
General Questions / Alignment specs
« on: April 23, 2022, 08:20:37 PM »
Anyone have suggestions on specs for caster/camber/toe in?
6
General Questions / LED headlights
« on: March 29, 2022, 04:02:46 PM »
Can anyone point me too some LED headlights that would plug right into our existing harness? Open to any style without the light bars for running lights and blinkers.
7
For Sale / New Wheels & Tires For Sale
« on: February 21, 2022, 04:25:06 PM »
New set of wheels & tires. Never seen asphalt. Located a bit east of Dallas Texas. New about $1900.00 Will sell for $1200.00 Will ship if buyer sets up the pickup. Email me @ bnelson7093@yahoo.com
Rear= Billet Specialties Street Lite Polished 17" X 11", 5" backspace, Micky Thompson Street Comp 315/35R17 tires
Front= Billet Specialties Street Lite Polished 17" X 8", 4.25" backspace, Micky Thompson Street Comp 245/45R17 tires
Rear= Billet Specialties Street Lite Polished 17" X 11", 5" backspace, Micky Thompson Street Comp 315/35R17 tires
Front= Billet Specialties Street Lite Polished 17" X 8", 4.25" backspace, Micky Thompson Street Comp 245/45R17 tires
8
General Questions / front quick jack body grommets
« on: February 09, 2022, 01:14:34 PM »
Where is everyone getting the body grommets for the front quick jack bolt holes? Seems like should be part of kit?
9
General Questions / Bear Claw door latches.
« on: November 26, 2021, 04:25:01 PM »
Anyone done Bear Claw door latches? I realize the ones supplied are period correct. But man they are a pain.
10
General Questions / Gas strut hood supports?
« on: November 19, 2021, 08:26:15 AM »
Has anyone done gas struts as opposed to the prop rod for hood support? If so, can you share P/N's and install info?
11
General Questions / wiper hole location
« on: November 06, 2021, 02:22:07 PM »
OK....So I'm about ready to mount the body back on the chassis and get to bodywork. Read that need to mount the wipers first due to access later.
My dilemma is the manual has three different measurements that contradict each other. See pic below. First says make marks 10" ether side of center at 4-3/4 from hood opening. OK. Simple. Then next it says you should now have two marks 10" off center 3" back from hood. How can that be when you just marked them 4-3/4" back. Then you look at the picture and it shows them 4-1/4" in back from the hood! WTF? Which is it?
My dilemma is the manual has three different measurements that contradict each other. See pic below. First says make marks 10" ether side of center at 4-3/4 from hood opening. OK. Simple. Then next it says you should now have two marks 10" off center 3" back from hood. How can that be when you just marked them 4-3/4" back. Then you look at the picture and it shows them 4-1/4" in back from the hood! WTF? Which is it?
12
General Questions / Header to footbox clearance
« on: October 10, 2021, 08:08:26 PM »
After bolting my headers in and re installing the tub. With tub all the way back on the rear frame rail, on drivers side, my header flange is actually touching the footbox. Do I need to move engine forward? Or is this typical? Right now my trans mount fits perfect, so if I move forward, will need to do some mods.
13
General Questions / Header gaskets for SBF stroker (351 windsor)
« on: October 03, 2021, 03:26:32 PM »
Whats everyone using for header gaskets? Everything I look at fits the inside holes and the supplied headers are using the outside holes. And I had to grind the crap out of the flange so the spark plug boots would go on the plugs 
14
General Questions / Firewall aluminum
« on: August 20, 2021, 01:33:15 PM »
Can anyone point me to a detailed discussion and pictures on the installation of the firewall aluminum? The manual su.....s 
shows pictures of a totally different firewall and describes lips and such that are non existent on the panels I have. Ive dug around a bit, but cant find anything detailed. I cant see how you can make these look acceptable with just butting up the raw edges to each other without bent lips that fold over the joints? Thinking about tossing them and just finishing off the fiberglass.
shows pictures of a totally different firewall and describes lips and such that are non existent on the panels I have. Ive dug around a bit, but cant find anything detailed. I cant see how you can make these look acceptable with just butting up the raw edges to each other without bent lips that fold over the joints? Thinking about tossing them and just finishing off the fiberglass.
15
General Questions / POR15
« on: July 10, 2021, 01:32:55 AM »
My chassis coming un coated. Anyone tried the POR15 chassis paint? Any suggestions on quality chassis paint?
Pages: [1] 2