Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mandmGuys

Pages: [1] 2 3 ... 10
1
General Questions / Re: Body weight
« on: June 18, 2018, 11:10:18 am »
I would say less than 200 LB Dad and I moved the body several times just the two of us. The brace front to rear cowl is very important. When going on and off the chassis you do need at least 4 bodies, you need to be able to float around and watch things and help flex the sides out past the tub.

2
General Questions / Re: New build HM-2022
« on: June 15, 2018, 10:05:52 am »
Welcome, ask away it what were here for.

3
General Questions / Re: Headed off to Lake City for another
« on: June 04, 2018, 02:13:53 pm »
Big Block FE  8) 8)

4
Important Information / Re: Hurricane Performance TV episode
« on: May 21, 2018, 10:15:00 am »
I see they have old episode's did anyone note what episode # the show was?

5
Build Pictures / Re: HM-2018 Build Thread
« on: May 03, 2018, 04:08:52 pm »
Russ I jumped back here as not to take the other thread too far off topic.  I had similar issue when we went to register I had bought the engine some 12 years prior from a judge (now deceased) bought the trans at local swap meet, the MOHP about had a stroke over it, we ended up filing a lawsuit against the DMV claiming ownership of all the items (motor, trans, etc.), after wining that they were very happy to help. Even let dad affix the state tag where we wanted. Funny thing was they gave us inspection sticker but never inspected it.

6
Build Pictures / Re: HM-2005 Build Thread
« on: March 16, 2018, 07:32:17 am »
Saw pictures of you and your bride out and about. Could tell you were smiling even from the side. Congrats.

7
Build Pictures / Re: HM-2005 Build Thread
« on: September 22, 2017, 09:01:19 am »
TCC 18, Amen to that. But how come I'm at almost 1000 miles and still working on things? Interior is really looking good there Russ.

Mark

8
General Questions / Re: Aluminum Firewall option...
« on: September 19, 2017, 07:20:47 am »
Cannot post one have not tried to fix photobucket yet. Send via email

Mark

9
General Questions / Re: Cockpit tub heat insulation...
« on: September 07, 2017, 07:26:07 am »
Aaron, I used the thin adhesive backed stuff that came with the kit in the engine side of the foot boxes before I installed the aluminum. In the cockpit I used a product call Rblock, which is about the same a dynamat or hushmat. It is a foil faced product that is some what adhesive and you cut and roll into place. I did almost the whole cockpit for heat and sound purposes.   
I have to figure out how to post pictures since all the photo bucket crap went down. Aaron, can you still access it?

Mark

10
Build Pictures / Re: HM-2005 Build Thread
« on: August 17, 2017, 07:13:23 am »
Looking good, ready to tackle the interior??

Mark

11
Build Pictures / Re: HM-2005 Build Thread
« on: August 09, 2017, 07:01:22 am »
Yippee - fun stuff there (did you really only drive it 40'?)

Mark

12
Build Pictures / Re: HM-2005 Build Thread
« on: July 17, 2017, 07:23:28 am »
Looking awesome - Cannot wait to see it outside  (in person).

Mark

13
Build Pictures / Re: HM-2005 Build Thread
« on: May 31, 2017, 07:30:53 am »
So do you still have a little trip planned this weekend? ;D  Really jealous that I am not going to be able to come down with the girls. 

14
General Questions / Re: Welcome
« on: April 25, 2017, 09:24:13 am »
Yeah, another Hurricane owner with a name I can remember. Welcome, and as Sam said give us some details this site needs some life.

Mark
HM2006

15
General Questions / Re: Assembling powertrain...
« on: March 24, 2017, 02:43:19 pm »
Aaron, I will add my two cents.
No Loctite on the bell housing, but I always use it on the Flywheel and clutch bolts (most of the time I use "red" unless I know I am going to be back soon).

If you don't have a cradle put your motor mounts on and set down on jack stands on either side, but keep some weight on the hoist while you assemble the clutch and bell. Needs to be fairly solid so you can wrench the motor over to dial in (remove the spark plugs - to make it easier).

On your X brace, probably not an issue yet but be sure to put the bolts in from the bottom so they don't become "trapped" after the tub is on.

Good luck - let us know if you get stuck.
Mark 

Pages: [1] 2 3 ... 10